...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
| Tip |
|---|
The exercises below illustrate the best practices for managing segments in a network. |
| Table of Contents |
|---|
Segment Naming
| Tip |
|---|
The Segments panel is where segments can be organized, grouped, zoomed to, selected, hidden or edited. |
...
...
Segment Groups
| Tip |
|---|
Grouping segments by name or data source can make it much easier to edit and interact with the network later on, especially if you have many interim pit ramps criss-crossing at different elevations. |
Editing segments in groups:
Go to the Segments panel and set the Grouped Fields to "Name".
Use the checkboxes to toggle visibility on and off.
Right Click in Viewport and choose "Zoom To" to center the group in the viewport.
...
...
Click in Viewport and choose "Select Coincident Points" to select all nodes in the pit/in the dump.
...
...
...
...
...
...
This turns off any roads which have this flag in their properties.
...
When the flag is turned off, this segment will not be traversable.
To add a flag to a schedule (.csv) file
Navigate to the sample data \NodesVersion folder.
Open ScheduleWithNodes.csv.
At the first empty column, add a column header "Ramp1Access".
Set values in the column to "OFF".
...
...
...
...
...
...
...
Map the fields to the column headers, including the "Ramp1Access" flag state.
...
...
Double click on the haul route in the list to display its animation in the viewport.
| Tip |
|---|
When activating hauls through the Schedule Auditor tab, those hauls will correspond to the flag states in the schedule. |
Gradient Tools
Haul Infinity has tools for drawing segments at a specified grade, and for applying grades to existing segments.
Gradient Draw Tool
To draw a ramp at ten percent grade:
Select the draw tool
.Set the snap mode to triangles
.Set the Gradient tool to 10%
.While in plan view, draw a road over the surface terrain.
Press <ESC> to exit the draw tool.
Turn off the Gradient tool by clicking on the "Gradient" text.
Rotate the viewport to see the 10% ramp.
Use this tool to draw ramps when you don't have an existing design to snap to.
Tooltips & Offsets
| Tip |
|---|
When drawing an interim ramp up the side of a pit or dump, use the tooltips and offset dialog to get the best results. |
Reading from tooltips:
Activate mouseover tooltips
.Select the draw tool and set the snap mode to triangles.
Find a spot at the toe of the dump and start drawing a ramp.
Hover the mouse over the next bench level to see the distance, bearing and gradient. Find a 10% gradient and continue the ramp.
...
...
Offsetting by coordinates:
Find the next point on the ramp that is approximately 10% grade.
Hold <CTRL> and left click to open the coordinate menu.
Change the gradient to exactly 10%.
Round the distance to the nearest whole number.
Press ОК to continue.
...
...
...
Set the relevant gradient for all segments between the two points.
Vertical Offset Tool
| Tip |
|---|
The Z-Offset tool can be used to draw elevated roads such as a skyway or overpass. |
Draw segments with vertical offset:
Set snap mode to triangles.
Select the draw tool.
Change the Z-offset to 10 meters
Draw road over the topo surface.
Press <ESC> to exit the draw tool.
Turn off the z-offset tool by clicking on the "Z-Offset" text.
...
...
Points can also be moved with the keyboard shortcut <F>.
...
...
...
In the Split within X metres of point window enter a distance in metres, such as 10.
...
...
...
Tooltips
When drawing a road, the tooltips will show the coordinates, distance, bearing and gradient of the point being drawn. This can be used to draw ramps at the correct grade over topo or designs.
To enable tooltips, press or the <Space> bar on the keyboard.
Coordinate Menu
| Tip |
|---|
When drawing roads, the coordinates menu accepts absolute and relative coordinates, and polar offsets. |
...
To open the coordinate menu:
Press keyboard shortcut <D> to begin drawing.
Draw a point on the network.
Hold <CTRL> and click to draw a new point.
The coordinate menu will open with the coordinates of the clicked point.
