Versions Compared

Old Version 5

changes.mady.by.user iarmstrong

Saved on

compared with

New Version Current

changes.mady.by.user iarmstrong

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

RU 🇷🇺

In the Parameters step enter the cycle time parameters for each combination of truck, loader, and material.

Table of Contents

Different payloads and load times may be used for each truck and material.

Fields with normal black text are editable - you can change values in these rows.

Fields with grey text are calculated – values in these rows vary depending on populated inputs.

Selections

When items are selected from the Trucks, Loaders and Materials lists in the Selections panel, they are added into the Parameters table.

  • Hold <CTRL> to select multiple items.

  • Hold <SHIFT> to select a list of items.

Image Modified

Cycle Time Calculations

Haul Infinity calculates cycle times from first principles using the payloads, swing times, and in-cycle delays.

Loader Payload Calculation

Image RemovedImage Added

  1. Enter the bucket payload and volume limit.

  2. Haul Infinity calculates the utilized bucket payload.

Truck Payload Calculation

Image RemovedImage Added

  1. Enter the truck tray payload and volume limit.

  2. Haul Infinity calculates the utilized tray payload.

Loading Calculation

  1. Enter the truck filling type:

    1. “FullBuckets” → less swings to fill the tray, some trucks light-loaded.

    2. “FullTrucks” → more swings to fill the tray, last bucket light-loaded.

    3. “Theoretical” → allow the digger to make "half a swing".

  2. Enter the loader cycle time (time to load one bucket).

  3. Enter the loader first pass delay (time to switch between trucks).

  4. Haul Infinity calculates the corresponding load times.

Detailed instructions on the cycle time calculation see here.

Overrides

Image RemovedImage Added

The Overrides section can be used to bypass the cycle time calculations.

For most users, Override inputs may be defined as follows:

Code Block
languagenone
Loader Load Time = Historical Load Time + Spot Time.
Truck Load Time = Historical Load Time.
Truck Payload = Payload (Ore, Waste).

If you are targeting a specific production rate, use:

Code Block
languagenone
Loader Load Time = Truck Payload / Production Rate.
Truck Load Time = Loader Load Time - Spot Time.
Truck Utilized Payload = Payload (Ore, Waste).

Make sure to override both Loader Load Time and Truck Load Time to capture the correct truck and loader rates.

Other Cycle Time Inputs

Image RemovedImage Added

Truck Matching Type

Select the truck matching type:

Code Block
languagenone
“OverTruck” → no digger wait time, some truck queue time.
“UnderTruck” → no truck wait time, some loader hang time.
“Round” → some truck queue time, some loader hang time (round the truck numbers to the nearest whole number).
“Theoretical” → zero queue or hang time (uses the theoretical number of trucks without rounding, allowing the fleet to have “half a truck”number (aof decimaltrucks numberminimun of trucks)1 or greater using decimal number.
“TheoreticalNoMinimum” → same as theoretical matching type, but not including minimum waiting timethe number of trucks can be less than 1 (whole number).
Tip

Tactical Scheduler users are recommended to use “Theoretical” matching for scheduling.

Minimum Queue Time

If queue time is already accounted for in the Time Usage Model, then set:

Code Block
languagenone
Truck Matching Type = “Theoretical”.
Minimum Queue Time = 0.

This removes queue time from the Haul Infinity cycle times.

Truck Spot Time at Loader

Enter the truck spotting time for each loader type.

Truck Dumping

If the historical truck dumping time includes the dump spot time, be sure to zero the "SpotAtDumpSeconds" property in Crusher/Stockpiles nodes on the network.

The impact of Truck Spot Time at Dump is dependent on whether Truck Matching is setup as Undertruck/Overtruck.

  • If Undertrucked, a minimum Queue time is assigned, and that is all that applies.

  • If Overtrucked the extra time in the cycle is applied to Queue Time. If no Dumping time is applied, these extra time is classified as Queue so the overall cycle time remains the same.

Recharge Travel Time Round Trip

If the truck is using power source Battery, then it will take into consideration the time taken to travel to a recharge location and back again.