...
| Tip |
|---|
In order to make cycle time calculations, Haul Infinity needs to know the |
...
Material type, |
...
Loader and |
...
Select Destination from Node. To do this: right click on a node > Show Path to > Loaded > Crusher > crusher required.
...
Show Return Route Between Nodes, as shown below.
...
You can also Select a node from Nodes panel tree.
...
Choose from History.
...
Hauls can be reactivated by selecting them from the History menu in the Route Selection panel.
Animations
Haulage animations can be turned on or off from the Animations button.
...
Truck type, as well as the Source and Destination for the material movement. |
| Table of Contents |
|---|
Route Selection
Enter route parameters:
Find the Route Selections panel to the left of the viewport.
...
Set material to "High Grade".
...
Set loader to EX2500.
...
Set truck to CAT 785D.
...
Set operating condition to "Normal".
Select a Material Type,specified in the Setup > Cycle Tims > Materials.
Select a Loader, specified in the Setup > Cycle Tims > Loaders.
Select a Truck, specified in the Setup > Trucks > Models.
Select Operating Conditions, specified in the Setup > Cycle Tims > Operating Conditions.
Showing a route from the Blocks
Select a Source block.
Hold down <CTRL> and select a Destination Block or Node.
Right-click and select “Show Return Route”.
The haul road from the Source to the Destination will be shown/animated in the Viewport.
Animation settings are available from the Animation menu in the top toolbar.
Colors and sizes of the Loaded and Unloaded Roads can be changed in the bottom Display tab > Entities panel.
To stop displaying haul road, use the blue cross button provided in the top toolbar. Alternatively, press <X> key.
Each of the shown haul routes will be listed in the History panel.
Click on the route to zoom to it in the Viewport.
Use the Eraser tool to clear all history.
Showing a route from the Nodes
Select a Source node.
Hold down <CTRL> and select a Destination Block or Node.
Right-click and select “Show Return Route”.
Or
Select a Source node.
Right-click and select “Show Path to”.
Select either “Loaded” or “Unloaded” route.
Select the Destination Node.
The haul road from the Source to the Destination will be shown/animated in the Viewport.
Animation settings are available from the Animation menu in the top toolbar.
Colors and sizes of the Loaded and Unloaded Roads can be changed in the bottom Display tab > Entities panel.
To stop displaying haul road, use the blue cross button provided in the top toolbar. Alternatively, press <X> key.
Each of the shown haul routes will be listed in the History panel.
Click on the route to reactivate it in the Viewport.
Use the Eraser tool to clear all history.
Animation Settings
Haulage animations can be turned On or Off from the Animations button.
Animations can slow down some calculations times. If you are using an older computer, turning animations
...
Off may help conserve performance.
...
In the dropdown menu specify the desired Animation Speed, and which elements (Trucks/Roads) you wish to animate.
By default, Loaded Route is shown in red, and Unloaded Route is shown in yellow. To change these colors, as well as these routes sizes, navigate to the Display bottom tab > Entities panel > Loaded Route and Unloaded Route settings.
Size of the Truck and Loader icons can also be changed in the Display bottom tab > Entities panel > Truck & Loader settings.
Press the blue cross button to stop the animation and clear displayed haul route. Alternatively, press <X> key.
...
Note
Activating haul route from Source to Destination is required to proceed to the network/truck times analysis.
Without an active haul route, you won’t see any data in the Segments tab, Charts tab, Truck Times tab and Cycle Time Analysis tab.
More details about the network analysis tools see in the sections:
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
For better understanding of Haul Infinity functionality go to the HI. Exercises page and complete the suggested tasks. |